bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Nissan NV 2500


  • Brake Controller Recommendation for a 2016 Nissan NV2500
  • For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. To install this in your 2016 Nissan NV 2500 all you need is the correct install harness part # 3050-P which is a confirmed fit. On your vehicle...
    view full answer...

  • Do Lippert Double Steps Fit Same Brackets as Lippert Triple Steps
  • The 3 step versions of the Lippert steps like the part # LC432687 are wider than most of the 2 steps like what you have. The difference in width is not unusual unfortunately. What you can do is move your current brackets out or remove them and use the outriggers # LC301704.
    view full answer...

  • Can Ventline Vanair Trailer Roof Vent Blow Either In or Out
  • No the Ventline Vanair Trailer Roof Vent # VP-543SP cannot be configured to run in an opposite direction as intended. While you can use two of these vents they will run in the same direction but do efficiently move 100 cubic feet per minute.
    view full answer...

  • 4-Way Wiring Harness Compatible with Tow Ready Mounting Bracket # 18144
  • If you are needing a trailer wiring harness for the 2018 Nissan NV 2500 that you have listed in the vehicle fit guide that will work with the Mounting Bracket # 18144, I recommend the Tekonsha T-One # 118553. This custom harness will plug into factory ports behind trim panels in the rear cargo area of the NV 2500 and the 4-Way will fit inside the bracket opening. If you are just looking for a universal hardware harness the Tekonsha 4-Pole # 18252 will work and is compatible with the bracket...
    view full answer...

  • Trailer Wiring Recommendation for 2014 Nissan NV 2500
  • Hey Martin, the trailer wiring I would recommend is the Tekonsha kit part # 118553 for your 2014 Nissan NV 2500 as it has a simpler install and has the most reliable converter box.
    view full answer...

  • Can an Aftermarket Mirror Add New Functions to a Vehicle
  • When installing an aftermarket mirror product like # KS68123-24N on any vehicle the vehicle must be already set up with wiring for each of the electrical functions on the mirror. So for example, if the vehicle were originally produced with mirrors that had only a power adjust feature you could not add a heated mirror function just by replacing the OEM mirror with an aftermarket one has this feature. The wiring for each function the mirror has must already be present on the vehicle. It...
    view full answer...

  • Recommended Tow Bar Light While Hauling Bikes
  • The easiest way to make sure your lights are visible when hauling bikes is using The Custer Wireless LED Tow Bar Light - Weatherproof - Magnetic Base - 23 inch Long - 7-Way Round # LIW-LDTL-7B. This weatherproof LED tow bar light provides stop, tail, side marker, and turn functions. It does have a wireless design and eliminates cords for hands-free control. The magnetic base offer up to 90 pounds of pull. The light has a low profile design that allows for easy handling and storage. I...
    view full answer...

  • Suspension Enhancement Options For 2020 Nissan NV 2500
  • Seems like you're needing some suspension enhancement! I recommend using the RoadActive kit # RAS3614-T. This will help your suspension from 0 to 100% travel. It's also adjustable to get the right amount of support. If that's not enough, get some helper springs # SSR-210-47 in the rear, these will only engage when your vehicle sags enough to hit the bump stops. If you're only looking to help the last half of your suspension travel and not hinder your smooth ride when you're not hauling,...
    view full answer...

  • Parts Needed to Install Redarc Tow-Pro Elite Brake Controller in 2013 Nissan NV 2500
  • Since your 2013 Nissan NV 2500 already has a working 4-way like part # 118553, you are on the money with the parts you need to install the Redarc brake controller: - Universal Installation Kit for Trailer Brake Controller # ETBC7 - Redarc Tow-Pro Elite Brake Controller # RED44FR - Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers # RED39FR These are the exact parts you will need to add the controller to your '13 NV 2500. The Elite will work with your Nissan, as...
    view full answer...

  • Cargo Area Mat Recommendation for a 2012 Nissan NV
  • The difference between the # VRNV11 and # VTNV11 that you referenced is that the # VTNV11 is made of thermoplastic whereas the # VRNV11 is made of carpet. The thermoplastic liner is a heavier, denser mat at 32 lbs when compared to the carpet version that is 18 lbs so it would be a better insulator so I would recommend it for you. Either would also fit with the factory floor liner removed and would work equally well with wire racks.
    view full answer...

  • Troubleshooting Trailer Turn Signals on 2015 Nissan NV 2500 Not Working
  • First thing you should do at this point is test the 7-way of the wiring harness with a circuit tester part # PTW2993 for voltage on all of the right pins when the taillight signals are being applied. Just like in the video I attached. If the voltage checks out there but the trailer lights still don't function right then the problem is on the trailer wiring. That would mean that problem is either due to a ground issue or a short issue. Make sure that the trailer side connector are clean...
    view full answer...

  • R-Value Rating for VanRug Custom Floor Mat for Cargo Vans
  • According to Bedrug, the R-value for the VanRug Custom Floor Mat for Cargo Vans # VRNV11 is 4.
    view full answer...

  • Troubleshooting Trailer 7k Axle with Locked Up Wheel
  • It's probably a bearing that got destroyed due to lack of lubrication which then caused it to look up to the axle's spindle. What you are going to want to do is take it all apart and see what the damage is. Remove the wheel, take off the dust cover of the hub, and then remove the spindle nut that holds the hub to the axle. Hopefully you can then pull the hub off of the axle easily. I'd assume you'd need a new hub/drum like with the part # 8-219-4UC3-EZ but it is possible you could get...
    view full answer...

  • Bike Rack For 2016 Nissan NV 2500
  • I do have an option for you but we do not carry a trunk mount bike rack at this time for the 2017 Nissan NV 2500. I think you will be much happier with a hitch mounted bike rack option on the Nissan NV because they are much more convenient compared to a trunk mount rack that you have to take on and off the vehicle all of the time. I recommend to add a no-drill custom fit Draw-Tite hitch part # 75715 on the van. I have attached an installation video for your reference. I recommend the...
    view full answer...

  • Brake Controller and Install Recommendation for a 2012 Nissan NV 2500
  • You will have to hardwire in a brake controller to your 2012 Nissan NV 2500 as there isn't a plug or port under the dash for quick installs. You will need to start with a 4-way (if you do not have one). For that you would want the # 118553. From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video...
    view full answer...

  • What Do I Need To Tow a Car Hauler Trailer With My 2012 Nissan NV 2500?
  • Yes, the Draw-Tite Max-Frame Trailer Hitch Receiver # 75715 will work for your 2012 Nissan NV 2500. Your Nissan will have a tow rating between 7000lbs and 9500lbs. You can contact Nissan for your exact tow rating by VIN number. The Draw-tite will allow for up to 7,000lbs towing and 1,125lbs of tongue weight. If you are using a weight distribution hitch the ratings are 10,000lbs towing and 1,000lbs of tongue weight. You will want to verify the weights of both your VW Passat and U-Haul...
    view full answer...

  • How Can I Haul 4 ebikes
  • I looked up the Rad Power Wagon, that spec shows a weight of 77 lbs. and depending on which model of the step through, those can weigh almost 70 lbs. Since you state that the other two are about 45 lbs. each, for that amount of combined weight you will be challenged to find a bike rack that has a listed weight rating needed. You can possibly use the Kuat NV 2.0 Bike Rack for 4 Bikes, # NV22G-NA22G if you can reduce each bikes weight enough to meet the 40 lbs. per bike rating of this rack....
    view full answer...

  • How to Complete the 12 Volt Accessory Circuit on the 7-Way of a 2013 Nissan NV 2500
  • First thing I would do is check the back of the 7-way to see if there is a wire attached to the 12 volt pin of the 7-way. This will be the 1:00 pin if you are looking into the connector from the front. If a wire is there then most likely you are missing a tow package relay under the hood. If there is nothing ran to that circuit, (or if you want to just fix the problem without any guesswork) you can run a length of 10 gauge wire from the 12 volt circuit pin of the 7-way through a 40 amp...
    view full answer...

  • Wiring Harness to Tow a Trailer with Brakes Using a 2012 Nissan NV2500
  • We have everything you need to get your 2012 Nissan NV2500 ready to tow a trailer but unfortunately there isn't a plug and play connector on your van for a brake controller. You also need to start with a 4-way, like part # HM11143585 that fits your van, before installing a 7-way. Once you have the 4-way use our # ETBC7 kit to convert it to the 7-way. The kit includes all of the wiring to connect a brake controller as well. I've linked a video of the kit being installed on an NV2500...
    view full answer...

  • Using a Generator on a GearDeck 17
  • The Gear Deck 17, part # H00604 is able to carry a generator, however, it is not recommended to run the generator with the fully removable lid installed. Our recommended use is to completely remove the lid and unpack the carrier and then use the telescoping base to slide the generator away from your vehicle prior to use. If your generator does have exhaust that points downward, I recommend removing the generator from the carrier prior to use. If you are looking to use the generator...
    view full answer...